Advantech BB-HD3-A3

SPHINX in Europa «  ch es uk fr at dk it nl be be  »
Tel..: +41 (0) 41 7673080 |  Impressum |  Kontakt |  EMail bitte hier klicken |  de  Deutsch « |  fr  Français |  it  Italiano

Sie sind hier » Optionen » Advantech BB-HD3-A3 «

Advantech BB-HD3-A3

J1708 & J1939 Heavy-duty Vehicle Interface Adapter



B+B SmartWorx Model HD3-A3, heavy-duty vehicle interface adapter, connects your onboard computer, wireless gateway, PC or laptop to the J1708/J1587 and J1939 bus found on most heavy-duty vehicles. The connection is made through a reliable, industry standard, wired, RS-232 interface.

Model HD3-A3 follows a simple operational protocol to communicate with the J1708 and J1939 bus, shielding the user from the complex vehicle interface. The HD3-A3 also solves timing problems often encountered when operating in Windows or other operating system environments. An embedded microprocessor handles buffering and bus timing, reducing data collisions, allowing vehicle data access with much greater precision than a non-intelligent interface adapter.

With the Streamer InTelematix database and algorithms, Model HD3-A3 provides a simple, operational protocol to communicate to the OBDII bus. The Command and Response Protocol Manual is available on B+B SmartWorx website.


Weitere Informationen


Wide OperatingTemperature -40 to 85 ºC (-40 to 185 ºF)
Input Voltage 10 to 42 VDC
Input Current @12 VDC 50 mA typical, 134 mA maximum
Enclosure Dimensions 104.1 x 43.2 x 20.3 mm
(4.1 x 1.7 x 0.8 in)
Cable Dimensions 533 mm (21 in) integrated Y-cable
Operating Voltage Range 8 to 30 VDC
MTBF (Meantime Before Failure) 174465 hours (19.9 years)
RS-232 DB9 female, DCE
Bus DB15 female
Pins 6,7 Ground
Pin 8 Power
Pins 9, 10 CAN low, CAN high (500k)
Pin 12, 13 CAN low, CAN high (250k)
Pins 14,15 J1708-, J1708+
Radiated RF Interference SAE J1113/41
Load Dump and Transient Protection SAE J1113/11
ESD Immunity SAE J1113/13
Environmental Testing
Temperature Test - Ten (10) temperature cycles as follows with unit operating normally:
1. Room (25 ºC) to Tmin in 15 minutes.
2. Soak at Tmin 1 hour with power removed from unit
3. Start unit at Tmin, confirm successful start by executing a command/response. Power-down unit. Maintain unit un-powered for one minute between power-ups.
4. Repeat Step 3 three times.
5. Start unit at Tmin and ramp Tmin to Tmax in 30 minutes
6. Operate at Tmax for 1 hour
7. Ramp Tmax to Tmin in 15 minutes
8. Repeat steps 1 through 7 nine times for a total of 10 cycles:
    a. 5 cycles at Vmin input
    b. 5 cycles at Vmax input
Vibration Testing
IEC 60068-2-6
10 sweeps of 10 to 500 to 10Hz at rate 0.5 oct/min. each axis
Level to be 10 to 36Hz, 0.06 in DA 36 to 500Hz, 4g’s
Unit must remain operational during and after the test
Shock Testing
IEC 60068-2-27
18 to 50g’s, 11ms, ½ sine pulses, 3 each direction each axis
Unit must remain operational during and after the test.
Drop Testing
IEC 60068-2-32
10 freefall drops from 1 meter onto concrete surface.
Drop 1 time one each face (6), 1 on a corner and the 3 edges of this corner.
The drop unit shall return to normal operation without physical damage.

Ordering Information

Available Modules
BB_HD3-A3 J1708 and J1939 Heavy Duty Vehicle Interface Adapter

ACCESSORIES - sold separately


Dokumentation PDF Advantech BB-HD3-A3 Datasheet (703.7 kB)

Copyright © 2013 SPHINX Computer Vertriebs-GmbH

AGB Datenschutzerklärung Nach oben Cookie Directive Standorte Über SPHINX Computer

Ok, verstanden

Diese Website verwendet Cookies.
Durch die Nutzung dieser Webseite erklären Sie sich damit einverstanden, dass Cookies gesetzt werden. Mehr erfahren.